YOU should be an Event Chair!

Derek DeLong · **Joined:** Mon Feb 18, 2013 11:39 am **Posts:** 45

Ok everyone. We have an update for all. The events through October are set and ready for your comments/concerns/general snide comments...

February 21, Test and Tune, Danville Regional Airport
February 22, Points Autocross #1, Danville Regional Airport
March 28, Novice School, Danville Regional Airport
March 29, Points Autocross #2, Danville Regional Airport
April 26, EV Challenge/Points Autocross #3, NCCAR (Circuit) = Event Chair: Mark Merrill and Roberta
May 16, Chick School, Danville Regional Airport = Chris Peterson & Gwen Habenicht & JJ
May 17, Points Autocross #4, Danville Regional Airport = Event Chair: Chris Peterson & Gwen Habenicht & JJ
June 27 & 28, Jimmy V Event (Points #5 & #6), Danville Regional Airport = Event Chair: Rob Keehner and Steven S.,
July 18, Points Event #7, NCCAR = Event Chair: Zach Williams and Jennifer Vance
August 2, Points Event #8, Virginia Motorsports Park = Event Chair: Lee Williams and Chris Vasquez
September 27, Points Autocross #9, NCCAR (Circuit) = Event Chair: TBD
October 3 & 4, zMAX Dragway - NCAC!!!!, subsequently also Points Events #10 & #11 = Event Chairs: Rob Keehner and Steve Spampinator and ALL AUTOX STAFF!
November ????? we shall see...

Have at it and we hope to see you all out there!

Lee Williams · **Joined:** Wed Sep 03, 2003 12:22 pm **Posts:** 75

Chris Vasques and I would like to volunteer to chair the August 2 event in Dinwiddie.

jennifer vance · **Joined:** Tue Feb 04, 2014 4:54 pm **Posts:** 1

zach w and I Want to event chair the July 18NCCAR event!

Steven Spampinato · **Posted:** Mon May 18, 2015 3:23 pm

Looking forward to chairing NCAC! :twisted:

We will have a turn around on the course each day!

JamesMilko · **Posted:** Mon May 18, 2015 4:35 pm

Copy this course and I'll show up.

https://www.youtube.com/watch?v=dU966ADlVIg

Chad Culbertson · **Posted:** Tue May 19, 2015 8:33 am

JamesMilko wrote:

Copy this course and I'll show up.

https://www.youtube.com/watch?v=dU966ADlVIg

lol, that was awesome, however, I think that course might exclude the entire CAM class.

Steven Carter · **Posted:** Tue May 19, 2015 9:12 am

Steven Spampinato wrote:

Looking forward to chairing NCAC! :twisted:

We will have a turn around on the course each day!

Dude, woah....slow down there. I know you are kidding, but don't. Srsly. :lol:

Jordan Normark · **Posted:** Tue May 19, 2015 3:25 pm

Chad Culbertson wrote:

JamesMilko wrote:

Copy this course and I'll show up.

https://www.youtube.com/watch?v=dU966ADlVIg

lol, that was awesome, however, I think that course might exclude the entire CAM class.

You CAM guys need to learn how to do 3 point turns :wink:

Steven Spampinato · **Posted:** Tue May 19, 2015 5:22 pm

Steven Carter wrote:

Steven Spampinato wrote:

Looking forward to chairing NCAC! :twisted:

We will have a turn around on the course each day!

Dude, woah....slow down there. I know you are kidding, but don't. Srsly. :lol:

Not kidding Rob Keehner and I enlisted to design the course last week.

Just because of that it will not be s2000 friendly....wait...can that actually be done? Not s2000 friendly? Is that even possible?

For real, we are going to do it!

Steven Spampinato · **Posted:** Tue May 19, 2015 5:23 pm

There will be an evil turn around right off the start! HAHAHAHAHAH! :twisted:

RickyBeam · **Posted:** Tue May 19, 2015 6:06 pm

Chad Culbertson wrote:

lol, that was awesome, however, I think that course might exclude the entire CAM class.

Just deal with it rallyx style... run square over it. :-) (or drive past, back up, and drive past. In a mustang, that'd likely be faster, and you'd still have tires afterwards.)

Arthur McDonald · **Joined:** Fri Aug 29, 2003 1:54 am **Posts:** 2052

Steven Spampinato wrote:

Just because of that it will not be s2000 friendly....wait...can that actually be done? Not s2000 friendly? Is that even possible?

I think that if you replicate one of Neal Harrington's favorite speed bumps from his North Hills neighborhood, you'll slow them down. Of course, Neal will be so mad he'll strip another spline.

BriceJohnson · **Joined:** Thu Apr 13, 2006 7:33 am **Posts:** 2230

We still need a chair for June's events. Please volunteer! If you only want to chair one day, thats ok also, just need some help. I don't wanna have to set up the course by myself.

Jordan Normark · **Posted:** Wed May 20, 2015 7:43 pm

I'll chair Jimmy V for the 27th and probably the 28th unless someone else really wants to. I need someone to come up with some bitchin' magnets since I lack computer and artistic skills. Maybe some cats "lickin" cancer...Yeah, I could really use help with the magnet design end of things.

Rob Keehner · **Posted:** Fri May 22, 2015 11:36 pm

I have magnets ready for anybody that needs one.

THSCC Forums

YOU should be an Event Chair!

Who is online